From theory to practice: Monitoring mechanical power output during wheelchair field and court sports using inertial measurement units.

An important performance determinant in wheelchair sports is the power exchanged between the athlete-wheelchair combination and the environment, in short, mechanical power. Inertial measurement units (IMUs) might be used to estimate the exchanged mechanical power during wheelchair sports practice. However, to validly apply IMUs for mechanical power assessment in wheelchair sports, a well-founded and unambiguous theoretical framework is required that follows the dynamics of manual wheelchair propulsion. Therefore, this research has two goals. First, to present a theoretical framework that supports the use of IMUs to estimate power output via power balance equations. Second, to demonstrate the use of the IMU-based power estimates during wheelchair propulsion based on experimental data. Mechanical power during straight-line wheelchair propulsion on a treadmill was estimated using a wheel mounted IMU and was subsequently compared to optical motion capture data serving as a reference. IMU-based power was calculated from rolling resistance (estimated from drag tests) and change in kinetic energy (estimated using wheelchair velocity and wheelchair acceleration). The results reveal no significant difference between reference power values and the proposed IMU-based power (1.8% mean difference, N.S.). As the estimated rolling resistance shows a 0.9-1.7% underestimation, over time, IMU-based power will be slightly underestimated as well. To conclude, the theoretical framework and the resulting IMU model seems to provide acceptable estimates of mechanical power during straight-line wheelchair propulsion in wheelchair (sports) practice, and it is an important first step towards feasible power estimations in all wheelchair sports situations.

Trunk motion influences mechanical power estimates during wheelchair propulsion.

In wheelchair sports, there is an increasing need to monitor mechanical power in the field. When rolling resistance is known, inertial measurement units (IMUs) can be used to determine mechanical power. However, upper body (i.e., trunk) motion affects the mass distribution between the small front and large rear wheels, thus affecting rolling resistance. Therefore, drag tests - which are commonly used to estimate rolling resistance - may not be valid. The aim of this study was to investigate the influence of trunk motion on mechanical power estimates in hand-rim wheelchair propulsion by comparing instantaneous resistance-based power loss with drag test-based power loss. Experiments were performed with no, moderate and full trunk motion during wheelchair propulsion. During these experiments, power loss was determined based on 1) the instantaneous rolling resistance and 2) based on the rolling resistance determined from drag tests (thus neglecting the effects of trunk motion). Results showed that power loss values of the two methods were similar when no trunk motion was present (mean difference [MD] of 0.6 ± 1.6 %). However, drag test-based power loss was underestimated up to -3.3 ± 2.3 % MD when the extent of trunk motion increased (r = 0.85). To conclude, during wheelchair propulsion with active trunk motion, neglecting the effects of trunk motion leads to an underestimated mechanical power of 1 to 6 % when it is estimated with drag test values. Depending on the required accuracy and the amount of trunk motion in the target group, the influence of trunk motion on power estimates should be corrected for.

Magnitude and variability of individual elbow load in repetitive baseball pitching.

In baseball pitchers the elbow is exposed to high and repetitive loads (i.e. external valgus torque), caused by pitching a high number of balls in a practice session or game. This can result in overuse injuries like the ulnar collateral ligament (UCL) injury. To understand injury mechanisms, the effect of repetitive pitching on the elbow load magnitude and variability was investigated. In addition, we explored whether repetitive pitching affects elbow muscle activation during pitching. Fifteen pitchers threw each 60 to 110 balls. The external valgus torque and electromyography of three elbow muscles were quantified during each pitch. Linear mixed model analyses were performed to investigate the effect of repetitive pitching. On a group level, the linear mixed models showed no significant associations of repetitive pitching with valgus torque magnitude and variability and elbow muscle activity. Significant differences exist between pitchers in their individual trajectories in elbow valgus torque and muscle activity with repetitive pitching. This shows the importance of individuality in relation to repetitive pitching. In order to achieve effective elbow injury prevention in baseball pitching, individual characteristics of changes in elbow load and muscle activity in relation to the development of UCL injuries should be investigated.

A Muscle Load Feedback Application for Strength Training: A Proof-of-Concept Study.

Muscle overload injuries in strength training might be prevented by providing personalized feedback about muscle load during a workout. In the present study, a new muscle load feedback application, which monitors and visualizes the loading of specific muscle groups, was developed in collaboration with the fitness company Gymstory. The aim of the present study was to examine the effectiveness of this feedback application in managing muscle load balance, muscle load level, and muscle soreness, and to evaluate how its actual use was experienced. Thirty participants were randomly distributed into 'control', 'partial feedback', and 'complete feedback' groups and monitored for eight workouts using the automatic exercise tracking system of Gymstory. The control group received no feedback, while the partial feedback group received a visualization of their estimated cumulative muscle load after each exercise, and the participants in the complete feedback group received this visualization together with suggestions for the next exercise to target muscle groups that had not been loaded yet. Generalized estimation equations (GEEs) were used to compare muscle load balance and soreness, and a one-way ANOVA was used to compare user experience scores between groups. The complete feedback group showed a significantly better muscle load balance (ß = -18.9; 95% CI [-29.3, -8.6]), adhered better to the load suggestion provided by the application (significant interactions), and had higher user experience scores for Attractiveness (p = 0.036), Stimulation (p = 0.031), and Novelty (p = 0.019) than the control group. No significant group differences were found for muscle soreness. Based on these results, it was concluded that personal feedback about muscle load in the form of a muscle body map in combination with exercise suggestions can effectively guide strength training practitioners towards certain load levels and more balanced cumulative muscle loads. This application has potential to be applied in strength training practice as a training tool and may help in preventing muscle overload.

Only Low Patients' Expectations Are Prognostic for Dissatisfaction With Performing Work-Related Knee-Straining Activities After Total Knee Arthroplasty: A Prospective Multicenter Cohort Study.

OBJECTIVE: To investigate whether preoperative expectations regarding performing work-related knee-straining activities were associated with being dissatisfied 6 months after total knee arthroplasty (TKA) among working patients, and, to identify prognostic factors for being dissatisfied with performing these work-related knee-straining activities. DESIGN: Multicenter prospective cohort study. SETTING: Orthopedic surgery departments of 7 hospitals in the Netherlands. PARTICIPANTS: A consecutive sample of 175 working patients who were on the waiting list for TKA (median age 59 years, 53% women) and intended to return to work (N=175). INTERVENTIONS: Not applicable. MAIN OUTCOME MEASURE(S): Dissatisfaction with performing work-related knee-straining activities 6 months postoperative was measured using the Work Osteoarthritis or joint-Replacement Questionnaire (score range 0-100). The clinically relevant cut-off points for being satisfied and dissatisfied were ≥71 and ≤50, respectively. RESULTS: Thirty-three patients (19%) were dissatisfied with performing work-related knee-straining activities 6 months after TKA. Patients who expected to be dissatisfied preoperative had a 5.1 times higher odds (95% CI 1.7-15.5) of being dissatisfied 6 months postoperatively compared with patients who expected to be satisfied preoperative. Regression analyses revealed that only patients' expectations were prognostic for being dissatisfied 6 months postoperatively rather than age, pain level, or having a knee-straining job. CONCLUSIONS: Two in 10 working patients are dissatisfied with performing work-related knee-straining activities 6 months after TKA. Only preoperative patients' expectations appeared prognostic. Therefore, we should better prepare working patients with low expectations by managing their preoperative expectations and improving their performance of work-related knee-straining activities in rehabilitation.

Feasibility and validity of a single camera CNN driven musculoskeletal model for muscle force estimation during upper extremity strength exercises: Proof-of-concept.

Muscle force analysis can be essential for injury risk estimation and performance enhancement in sports like strength training. However, current methods to record muscle forces including electromyography or marker-based measurements combined with a musculoskeletal model are time-consuming and restrict the athlete's natural movement due to equipment attachment. Therefore, the feasibility and validity of a more applicable method, requiring only a single standard camera for the recordings, combined with a deep-learning model and musculoskeletal model is evaluated in the present study during upper-body strength exercises performed by five athletes. Comparison of muscle forces obtained by the single camera driven model against those obtained from a state-of-the art marker-based driven musculoskeletal model revealed strong to excellent correlations and reasonable RMSD's of 0.4-2.1% of the maximum force (Fmax) for prime movers, and weak to strong correlations with RMSD's of 0.4-0.7% Fmax for stabilizing and secondary muscles. In conclusion, a single camera deep-learning driven model is a feasible method for muscle force analysis in a strength training environment, and first validity results show reasonable accuracies, especially for prime mover muscle forces. However, it is evident that future research should investigate this method for a larger sample size and for multiple exercises.

Energy flow through the lower extremities in high school baseball pitching.

It is generally accepted that most of the energy transferred to the ball during a baseball pitch is generated in the trunk and lower extremities. Therefore, purpose of this study was to assess the energy flow through the lower extremities during a baseball pitch. It was hypothesised that the (stabilising) leading leg mainly transfers energy in a distal-to-proximal order as a kinetic chain while the (driving) trailing leg generates most energy, primarily at the hip. A joint power analysis was used to determine the rates of energy (power) transfer and generation in the ankles, knees, hips and lumbosacral joint (L5-S1) for 22 youth pitchers. Analyses showed that the leading leg mainly transfers energy upwards in a distal-to-proximal order just before stride foot contact. Furthermore, energy generation was higher in the trailing leg and primarily arose from the trailing hip. In conclusion, the legs contribute differently to the energy flow where the leading leg acts as an initial kinetic chain component and the trailing leg drives the pitch by generating energy. The actions of both legs are combined in the pelvis and passed on to the subsequent, more commonly discussed, open kinetic chain starting at L5-S1.

Responsiveness of Daily Life Gait Quality Characteristics over One Year in Older Adults Who Experienced a Fall or Engaged in Balance Exercise.

Gait quality characteristics obtained from daily-life accelerometry are clinically relevant for fall risk in older adults but it is unknown whether these characteristics are responsive to changes in gait quality. We aimed to test whether accelerometry-based daily-life gait quality characteristics are reliable and responsive to changes over one year in older adults who experienced a fall or an exercise intervention. One-week trunk acceleration data were collected from 522 participants (65-97 years), at baseline and after one year. We calculated median values of walking speed, regularity (sample entropy), stability (logarithmic rate of divergence per stride), and a gait quality composite score, across all 10-s gait epochs derived from one-week gait episodes. Intraclass correlation coefficients (ICC) and limits of agreement (LOA) were determined for 198 participants who did not fall nor participated in an exercise intervention during follow-up. For responsiveness to change, we determined the number of participants who fell (n = 209) or participated in an exercise intervention (n = 115) that showed a change beyond the LOA. ICCs for agreement between baseline and follow-up exceeded 0.70 for all gait quality characteristics except for vertical gait stability (ICC = 0.69, 95% CI [0.62, 0.75]) and walking speed (ICC = 0.68, 95% CI [0.62, 0.74]). Only walking speed, vertical and mediolateral gait stability changed significantly in the exercisers over one year but effect sizes were below 0.2. The characteristic associated with most fallers beyond the LOA was mediolateral sample entropy (4.8% of fallers). For the exercisers, this was gait stability in three directions and the gait quality composite score (2.6% of exercisers). The gait quality characteristics obtained by median values over one week of trunk accelerometry were not responsive to presumed changes in gait quality after a fall or an exercise intervention in older people. This is likely due to large (within subjects) differences in gait behaviour that participants show in daily life.

Obtaining wheelchair kinematics with one sensor only? The trade-off between number of inertial sensors and accuracy for measuring wheelchair mobility performance in sports.

In wheelchair sports, the use of Inertial Measurement Units (IMUs) has proven to be one of the most accessible ways for ambulatory measurement of wheelchair kinematics. A three-IMU configuration, with one IMU attached to the wheelchair frame and two IMUs on each wheel axle, has previously shown accurate results and is considered optimal for accuracy. Configurations with fewer sensors reduce costs and could enhance usability, but may be less accurate. The aim of this study was to quantify the decline in accuracy for measuring wheelchair kinematics with a stepwise sensor reduction. Ten differently skilled participants performed a series of wheelchair sport specific tests while their performance was simultaneously measured with IMUs and an optical motion capture system which served as reference. Subsequently, both a one-IMU and a two-IMU configuration were validated and the accuracy of the two approaches was compared for linear and angular wheelchair velocity. Results revealed that the one-IMU approach show a mean absolute error (MAE) of 0.10 m/s for absolute linear velocity and a MAE of 8.1°/s for wheelchair angular velocity when compared with the reference system. The two-IMU approach showed similar differences for absolute linear wheelchair velocity (MAE 0.10 m/s), and smaller differences for angular velocity (MAE 3.0°/s). Overall, a lower number of IMUs used in the configuration resulted in a lower accuracy of wheelchair kinematics. Based on the results of this study, choices regarding the number of IMUs can be made depending on the aim, required accuracy and resources available.

Various Workload Models and the Preseason Are Associated With Injuries in Professional Female Cyclists.

PURPOSE: To determine if workload and seasonal periods (preseason vs in season) are associated with the incidence of injuries and illnesses in female professional cyclists. METHODS: Session rating of perceived exertion was used to quantify internal workload and was collected from 15 professional female cyclists, from 33 athlete seasons. One week (acute) workload, 4 weeks (chronic) workload, and 3 acute:chronic workload models were analyzed. Two workload models are based on moving averages of the ratios, the acute:chronic workload ratio (ACWR), and the ACWR uncoupled (ACWRuncoup). The difference between both is the chronic load; in ACWR, the acute load is part of the chronic load, and in ACWRuncoup, the acute and chronic load are uncoupled. The third workload model is based on exponentially weighted moving averages of the ratios. In addition, the athlete season is divided into the preseason and in season. RESULTS: Generalized estimating equations analysis was used to assess the associations between the workload ratios and the occurrence of injuries and illnesses. High values of acute workload (P = .048), ACWR (P = .02), ACWRuncoup (P = .02), exponentially weighted moving averages of the ratios (P = .01), and the in season (P = .0001) are significantly associated with the occurrence of injury. No significant associations were found between the workload models, the seasonal periods, and the occurrence of illnesses. CONCLUSIONS: These findings suggest the importance of monitoring workload and workload ratios in female professional cyclists to lower the risk of injuries and therefore improve their performances. Furthermore, these results indicate that, in the preseason, additional stressors occur, which could lead to an increased risk of injuries.

Establishing the Role of Elbow Muscles by Evaluating Muscle Activation and Co-contraction Levels at Maximal External Rotation in Fastball Pitching.

Background: Baseball pitching is associated with a high prevalence of ulnar collateral ligament injuries, potentially due to the high external valgus load on the medial side of the elbow at the instant of maximal shoulder external rotation (MER). In-vitro studies show that external valgus torque is resisted by the ulnar collateral ligament but could also be compensated by elbow muscles. As the potential active contribution of these muscles in counteracting external valgus load during baseball pitching is unknown, the aim of this study is to determine whether and to what extent the elbow muscles are active at and around MER during a fastball pitch in baseball. Methods: Eleven uninjured pitchers threw 15 fastball pitches. Surface electromyography of six muscles crossing the elbow were measured at 2000 Hz. Electromyography signals were normalized to maximal activity values. Co-contraction index (CCI) was calculated between two pairs of the flexor and extensor elbow muscles. Confidence intervals were calculated at the instant of MER. Four ranges of muscle activity were considered; 0-20% was considered low; 21-40% moderate; 41-60% high and over 60% as very high. To determine MER, the pitching motion was captured with a highspeed camera at 240 Hz. Results: The flexor pronator mass, pronator teres, triceps brachii, biceps brachii, extensor supinator mass and anconeus show moderate activity at MER. Considerable variation between participants was found in all muscles. The CCI revealed co-contraction of the two flexor-extensor muscle pairs at MER. Interpretation: The muscle activation of the flexor and pronator muscles at MER indicates a direct contribution of forearm muscles crossing the medial side of the elbow in counteracting the external valgus load during fastball pitching. The activation of both flexor and extensor muscles indicates an in-direct contributory effect as the combined activity of these muscles counteract opening of the humeroulnar joint space. We believe that active muscular contributions counteracting the elbow valgus torque can be presumed to relieve the ulnar collateral ligament from maximal stress and are thus of importance in injury risk assessment in fastball pitching in baseball.

Machine Learning to Improve Orientation Estimation in Sports Situations Challenging for Inertial Sensor Use.

In sports, inertial measurement units are often used to measure the orientation of human body segments. A Madgwick (MW) filter can be used to obtain accurate inertial measurement unit (IMU) orientation estimates. This filter combines two different orientation estimates by applying a correction of the (1) gyroscope-based estimate in the direction of the (2) earth frame-based estimate. However, in sports situations that are characterized by relatively large linear accelerations and/or close magnetic sources, such as wheelchair sports, obtaining accurate IMU orientation estimates is challenging. In these situations, applying the MW filter in the regular way, i.e., with the same magnitude of correction at all time frames, may lead to estimation errors. Therefore, in this study, the MW filter was extended with machine learning to distinguish instances in which a small correction magnitude is beneficial from instances in which a large correction magnitude is beneficial, to eventually arrive at accurate body segment orientations in IMU-challenging sports situations. A machine learning algorithm was trained to make this distinction based on raw IMU data. Experiments on wheelchair sports were performed to assess the validity of the extended MW filter, and to compare the extended MW filter with the original MW filter based on comparisons with a motion capture-based reference system. Results indicate that the extended MW filter performs better than the original MW filter in assessing instantaneous trunk inclination (7.6 vs. 11.7° root-mean-squared error, RMSE), especially during the dynamic, IMU-challenging situations with moving athlete and wheelchair. Improvements of up to 45% RMSE were obtained for the extended MW filter compared with the original MW filter. To conclude, the machine learning-based extended MW filter has an acceptable accuracy and performs better than the original MW filter for the assessment of body segment orientation in IMU-challenging sports situations.

The short- and long-term temporal relation between falls and concern about falling in older adults without a recent history of falling.

BACKGROUND AND AIM: The reciprocal relation between falling and concern about falling is complex and not well understood. We aimed to determine whether concern about falling increases after a fall and whether concern about falling increases the odds of future falls in community-dwelling older adults without a recent fall history. METHODS: We selected 118 community-dwelling older adults (mean age: 71.4 (SD: 5.3) years) without a self-reported history of falling, one year prior to baseline assessment, from the one-year VIBE cohort for analyses. On a monthly basis, we recorded concern about falling (using the Falls Efficacy Scale-International, FES-I), as well as the occurrence of falls (through questionnaires and telephone calls). We determined 1) whether falling predicts an increase in concern about falling and 2) whether a high concern about falling is predictive of falling. Standard linear (fixed-effects) regression and mixed effects regression analyses were performed over long-term, i.e. one year, and short-term, i.e. one-month, intervals, respectively and were adjusted for gender, age and physical activity (quantified as the average total walking duration per day). Analyses were performed separately for all reported falls and for injurious falls only. RESULTS: High concern about falling at baseline did not predict falls over the course of one year, nor over the course of one month. Furthermore, falls in between baseline assessment and one year thereafter did not predict increased concern about falling from baseline to one year later, independent of whether all falls or only injurious falls were considered. However, falls, either all or injurious only, happening somewhere over the course of a one-month interval, significantly predicted small increases in concern about falling (1.49 FES-I points, 95% CI [0.74, 2.25], p<0.001 for all falls; 2.60 FES-I points, 95% CI [1.55, 3.64], p<0.001 for injurious falls) from the start to the end of that one-month interval. CONCLUSION: Older adults without a recent history of falling seem to be resilient against developing concern about falling after having fallen, resulting in a short-term temporary effect of falling on concern about falling. Furthermore, we found no evidence that a high concern about falling predicts future falls over a one-month or a one-year follow-up period, suggesting that concern is not a primary cause for falls in older adults without a recent history of falling.

Marker location and knee joint constraint affect the reporting of overhead squat kinematics in elite youth football players.

Motion capture systems are used in the analysis and interpretation of athlete movement patterns for a variety of reasons, but data integrity remains critical regardless. The extent to which marker location or constraining degrees of freedom (DOF) in the biomechanical model impacts on this integrity lacks consensus. Ten elite academy footballers performed bilateral overhead squats using a marker-based motion capture system. Kinematic data were calculated using four different marker sets with 3DOF and 6DOF configurations for the three joint rotations of the right knee. Root mean squared error differences between marker sets ranged in the sagittal plane between 1.02 and 4.19 degrees to larger values in the frontal (1.30-6.39 degrees) and transverse planes (1.33 and 7.97 degrees). The cross-correlation function of the knee kinematic time series for all eight marker-sets ranged from excellent for sagittal plane motion (>0.99) but reduced for both coronal and transverse planes (<0.9). Two-way ANOVA repeated measures calculated at peak knee flexion revealed significant differences between marker sets for frontal and transverse planes (p < 0.05). Pairwise comparisons showed significant differences between some marker sets. Marker location and constraining DOF while measuring relatively large ranges of motion in this population are important considerations for data integrity.

Association between Daily-Life Gait Quality Characteristics and Physiological Fall Risk in Older People.

Gait quality characteristics obtained from accelerometry during daily life are predictive of falls in older people but it is unclear how they relate to fall risk. Our aim was to test whether these gait quality characteristics are associated with the severity of fall risk. We collected one week of trunk accelerometry data from 279 older people (aged 65-95 years; 69.5% female). We used linear regression to investigate the association between six daily-life gait quality characteristics and categorized physiological fall risk (QuickScreen). Logarithmic rate of divergence in the vertical (VT) and anteroposterior (AP) direction were significantly associated with the level of fall risk after correction for walking speed (both p < 0.01). Sample entropy in VT and the mediolateral direction and the gait quality composite were not significantly associated with the level of fall risk. We found significant differences between the high fall risk group and the very low- and low-risk groups, the moderate- and very low-risk and the moderate and low-risk groups for logarithmic rate of divergence in VT and AP (all p ≤ 0.01). We conclude that logarithmic rate of divergence in VT and AP are associated with fall risk, making them feasible to assess the physiological fall risk in older people.

Gait quality assessed by trunk accelerometry after total knee arthroplasty and its association with patient related outcome measures.

BACKGROUND: With an increasingly younger population and more active patients, assessment of functional outcome is more important than ever in patients undergoing total knee arthroplasty. Accelerometers have been used successfully to objectively evaluate gait quality in other fields. The aim of this study was to assess gait quality with accelerometers before and after surgery, and to assess added value of resulting parameters to patient reported outcome measures scores. METHODS: Sixty-five patients (mean age 65 years (range 41-75)) who underwent primary total knee arthroplasty were evaluated using a tri-axial trunk accelerometer preoperatively and 1 year after surgery. Gait quality parameters derived from the accelerometry data were evaluated in three dimensions at both time points. Factor analysis was performed on all outcome variables and changes from before to 1 year after surgery in the most representative variable for each factor were studied. FINDINGS: Factor analysis identified three separate gait quality factors, with questionnaire and gait quality parameters loading on different factors. Both gait quality factor scores and questionnaire factor scores improved significantly 1 year after surgery. As expected based on the factor analysis, only weak to moderate associations were found between patient reported outcome measures and gait quality before surgery, after surgery and in change scores. INTERPRETATION: The independence of patient reported outcome measures and gait quality parameters measured with trunk accelerometry indicates that gait quality parameters provide additional information on functional outcome after total knee arthroplasty. Providing caretakers with objectively measurable targets using accelerometry could help improve outcome of these patients.

Three Out of Ten Working Patients Expect No Clinical Improvement of Their Ability to Perform Work-Related Knee-Demanding Activities After Total Knee Arthroplasty: A Multicenter Study.

Purpose Three out of ten patients do not return to work after total knee arthroplasty (TKA). Patient expectations are suggested to play a key role. What are patients' expectations regarding the ability to perform work-related knee-demanding activities 6 months after TKA compared to their preoperative status? Methods A multi-center cross-sectional study was performed among 292 working patients listed for TKA. The Work Osteoarthritis or joint-Replacement Questionnaire (WORQ, range 0-100, minimal important difference 13) was used to assess the preoperatively experienced and expected ability to perform work-related knee-demanding activities 6 months postoperatively. Differences between the preoperative and expected WORQ scores were tested and the most difficult knee-demanding work-related activities were described. Results Two hundred thirty-six working patients (81%) completed the questionnaire. Patients' expected WORQ score (Median = 75, IQR 60-86) was significantly (p < 0.01) higher than their preoperative WORQ score (Median = 44, IQR 35-56). A clinical improvement in ability to perform work-related knee-demanding activities was expected by 72% of the patients, while 28% of the patients expected no clinical improvement or even worse ability to perform work-related knee-demanding activities 6 months after TKA. Of the patients, 34% expected severe difficulty in kneeling, 30% in crouching and 17% in clambering 6 months after TKA. Conclusions Most patients have high expectations, especially regarding activities involving deep knee flexion. Remarkably, three out of ten patients expect no clinical improvement or even a worse ability to perform work-related knee-demanding activities 6 months postoperatively compared to their preoperative status. Therefore, addressing patients expectations seems useful in order to assure realistic expectations regarding work activities.

To Improve Your Surgical Drilling Skills, Make Use of Your Index Fingers.

BACKGROUND: Surgery has greatly benefited from various technologic advancements over the past decades. Surgery remains, however, mostly manual labor performed by well-trained surgeons. Little research has focused on improving osseous drilling techniques. The objective of this study was to compare the accuracy and precision of different orthopaedic drilling techniques involving the use of both index fingers. QUESTIONS/PURPOSES: (1) Does the shooting grip technique and aiming at the contralateral index finger improve accuracy and precision in drilling? (2) Is the effect of drilling technique on accuracy and precision affected by the experience level of the performer? METHODS: This study included 36 participants from two Dutch training hospitals who were subdivided into three groups (N = 12 per group) based on their surgical experience (that is, no experience, residents, and surgeons). The participants had no further experience with drilling outside the hospital nor were there other potential confounding variables that could influence the test outcomes. Participants were instructed to drill toward a target exit point on a synthetic bone model. There were four conditions: (1) clenched grip without aiming; (2) shooting grip without aiming; (3) clenched grip with aiming at the contralateral index finger; and (4) shooting grip aiming at the contralateral index finger. Participants were only used to a clenched grip without aiming in clinical practice. Each participant had to drill five times per technique per test, and the test was repeated after 4 weeks. Accuracy was defined as the systematic error of all measurements and was calculated as the mean of the five distances between the five exit points and the target exit point, whereas precision was defined as the random error of all measurements and calculated as the SD of those five distances. Accuracy and precision were analyzed using mixed-design analyses of variance. RESULTS: Accuracy was highest when using a clenched grip with aiming at the index finger (mean 4.0 mm, SD 1.1) compared with a clenched grip without aiming (mean 5.0 mm, SD 1.2, p = 0.004) and a shooting grip without aiming (mean 4.9 mm, SD 1.4, p = 0.015). The shooting grip with aiming at the index finger (mean 4.1 mm, SD 1.2) was also more accurate than a clenched grip without aiming (p = 0.006) and a shooting grip without aiming (p = 0.014). Shooting grip with aiming at the opposite index finger (median 2.0 mm, interquartile range [IQR] 1.2) showed the best precision and outperformed a clenched grip without aiming (median 2.9 mm, IQR 1.1, p = 0.016), but was not different than the shooting grip without aiming (median 2.2 mm, IQR 1.4) or the clenched grip with aiming (median 2.4 mm, IQR 1.3). The accuracy of surgeons (mean 4.1 mm, SD 1.1) was higher than the inexperienced group (mean 5.0 mm, SD 1.1, p = 0.012). The same applied for precision (median 2.2 mm, IQR 1.0 versus median 2.8 mm, IQR 1.4, p = 0.008). CONCLUSIONS: A shooting grip combined with aiming toward the index finger of the opposite hand had better accuracy and precision compared with a clenched grip alone. Based on this study, experience does matter, because the orthopaedic surgeons outperformed the less experienced participants. Based on our study, we advise surgeons to aim at the index finger of the opposite hand when possible and to align the ipsilateral index finger to the drill bit. LEVEL OF EVIDENCE: Level II, therapeutic study.

Improving Mobility Performance in Wheelchair Basketball.

OBJECTIVE: This study aimed to investigate which characteristics of athlete, wheelchair and athlete-wheelchair interface are the best predictors of wheelchair basketball mobility performance. DESIGN: A total of 60 experienced wheelchair basketball players performed a wheelchair mobility performance test to assess their mobility performance. To determine which variables were the best predictors of mobility performance, forward stepwise linear regression analyses were performed on a set of 33 characteristics, including 10 athlete, 19 wheelchair, and 4 athlete-wheelchair interface characteristics. RESULTS: A total of 8 of the characteristics turned out to be significant predictors of wheelchair basketball mobility performance. Classification, experience, maximal isometric force, wheel axis height, and hand rim diameter-which both are interchangeable with each other and wheel diameter-camber angle, and the vertical distance between shoulder and rear wheel axis-which was interchangeable with seat height-were positively associated with mobility performance. The vertical distance between the front seat and the footrest was negatively associated with mobility performance. CONCLUSION: With this insight, coaches and biomechanical specialists are provided with statistical findings to determine which characteristics they could focus on best to improve mobility performance. Six out of 8 predictors are modifiable and can be optimized to improve mobility performance. These adjustments could be carried out both in training (maximal isometric force) and in wheelchair configurations (eg, camber angle).

Where to Step? Contributions of Stance Leg Muscle Spindle Afference to Planning of Mediolateral Foot Placement for Balance Control in Young and Old Adults.

Stable gait requires active control of the mediolateral (ML) kinematics of the body center of mass (CoM) and the base of support (BoS) in relation to each other. Stance leg hip abductor (HA) muscle spindle afference may be used to guide contralateral swing foot placement and adequately position the BoS in relation to the CoM. We studied the role of HA spindle afference in control of ML gait stability in young and older adults by means of muscle vibration. Healthy young (n = 12) and older (age > 65 years, n = 18) adults walked on a treadmill at their preferred speed. In unperturbed trials, individual linear models using each subject's body CoM position and velocity at mid-swing as inputs accurately predicted foot placement at the end of the swing phase in the young [mean R2 = 0.73 (SD 0.11)], but less so in the older adults [mean R2 = 0.60 (SD 0.14)]. In vibration trials, HA afference was perturbed either left or right by vibration (90 Hz) in a random selection of 40% of the stance phases. After vibrated stance phases, but not after unvibrated stance phases in the same trials, the foot was placed significantly more inward than predicted by individual models for unperturbed gait. The effect of vibration was stronger in young adults, suggesting that older adults rely less on HA spindle afference. These results show that HA spindle afference in the stance phase of gait contributes to the control of subsequent ML foot placement in relation to the kinematics of the CoM, to stabilize gait in the ML direction and that this pocess is impaired in older adults.